Skyjacker TU761PRS User Manual download pdf

2007 - 2012 Toyota Tundra

6” Suspension Lift

Installation Instructions

REQUIRED TOOL LIST:

* Safety Glasses

* Metric / Standard Wrenches & Sockets

* Allen Wrenches

* Assorted Drill Bits

* Floor Jack

* Jack Stands

* Measuring Tape

* Torque Wrench

* Reciprocating Saw (4WD Models)

* Grinder (4WD Models)

* Welding Machine (4WD Models)

www.skyjacker.com

I-TU761 REV5 7-12 Pg 1

Before beginning the installation, thoroughly & completely read these instructions & the enclosed

driver’s WARNING NOTICE. Affix the WARNING decal in the passenger compartment in clear view

of all occupants. Refer to the Parts List to insure that all parts & hardware are received prior to the

disassembly of the vehicle. If any parts are found to be missing, contact SKYJACKER

Customer

Service at 318-388-0816 to obtain the needed items. If you have any questions or reservations

about installing this lift kit, contact SKYJACKER

Technical Assistance at 318-388-0816.

Make sure you park the vehicle on a level concrete or asphalt surface. Many times a vehicle is not

level (side-to-side) from the factory & is usually not noticed until a lift kit has been installed which

makes the difference more visible. Using a measuring tape, measure the front & rear (both sides)

from the ground up to the center of the fender opening above the axle. Record this information

below for future reference.

Driver Side Front: Passenger Side Front:

Driver Side Rear: Passenger Side Rear:

IMPORTANT NOTES:

• OEM wheels can not be reused in the installation of this suspension lift. 17" diameter or larger

wheels must be used to install this suspension lift.

• This lift is determined from the amount of lift to the front of the vehicle, while only lifting the rear to

a position level with the front.

• If larger tires (10% more than the stock diameter) are installed, speedometer recalibration will be

necessary. Contact your local Toyota dealer or an authorized dealer for details.

• After installation, a qualified alignment facility is required to align the vehicle to the OEM

specifications.

1 2 3 4 5 6 7 8 9 10

Summary of Contents

Page 1

2007 - 2012 Toyota Tundra 6” Suspension LiftInstallation InstructionsREQUIRED TOOL LIST:* Safety Glasses * Metric / Standard Wrenches & Sockets*

Page 2 - Kit Box Breakdown:

I-TU761 Pg 10Seat Belts Save Lives, Please Wear Your Seat Belt.TORQUE SPECIFICATIONSINCH SYSTEMBolt Size Grade 5 Grade 85

Page 3 - TU761PRS:

Pg 2I-TU761 Kit Box Breakdown:TU761A:ITEM# DESCRIPTION QTYTU756STS Tundra Performance Strut

Page 4 - Front Installation:

HB-TU76-CM ITEM# DESCRIPTION QTY18x50MMB 18MM x 50MM- 2.5” TPI Bolt 418MMFW 5/8” - A325 Flat Washer 818MMN 18MM-2.

Page 5

I-TU761 Pg 4Front Installation:1. With the vehicle on flat level ground, set the emergency brake & block the rear tires / wheels. Place a fl

Page 6

I-TU761 Pg 5 9. 4WD Models: Support the front differential with a transmission jack. (See Photo # 8)10. 4WD Models: Remove the differential

Page 7

I-TU761 Pg 615. Install the new Skyjacker rear cross member using the supplied 18MM bolts, washers, & nuts. Note: Do not tighten the hardware com

Page 8 - Rear Installation:

20. Install the OEM coil & top assembly to the new Skyjacker strut. Note: There are four snap ring grooves located on the new Skyjacker

Page 9

26. Install the new Skyjacker front brake line extension brackets using the OEM hardware & the supplied 5/16" x 3/4" bolts & n

Page 10

6. Install the new Skyjacker u-bolts. (See Photo # 34) 7. Install the new Skyjacker rear shocks using the OEM hardware. 8. Install the new Skyj

Related models: TU761PR | TU761A |

Comments to this Manuals

No comments

Skyjacker TU761PRS User Manual

Browse online or download User Manual for For the car Skyjacker TU761PRS. Skyjacker TU761PRS User Manual

Summary of Contents

Related models: TU761PR | TU761A |

Comments to this Manuals

Related products and manuals for For the car Skyjacker TU761PRS