Skyjacker TC530 User Manual download pdf

IMPORT

ANT NOTES

-Skyjacker strongly advises taking extreme caution when working with loaded coil springs to

prevent accident or harm.

-Trucks w/o manual locking hubs, height must not be adjusted over 2" above factory height.

-Both coil over assemblies should be adjusted to the same length after installation. It is VERY

IMPORTANT that after installation the coil does not have any slack between the mounting

cups. At no time during axle travel should the coil lose contact with the mounting points.

-When final adjustments are made the setscrew MUST be tightened. At no time should the

coil over assembly be ran without the set screw being tight.

Part # Description Qty

TOY20153-S 2.5-3" COIL-2" COIL 2

SKY201-S SKYJACKER 2" SHOCK 2

T5USM-B UPPER SHOCK MOUNT 2

T5SBB-S SWAY BAR LOWERING BLOCK 2

916X212X7U 9/16 X 2 1/2 X 7 U-BOLT SQUARE 4

716X1FTB 7/16 X 1 BOLT,FINE THD GRD8 6

12X212FTB 1/2 X 2 1/2 FINE THRD BOLT 2

716FTN 7/16-20 FINE N/I LOCK NUT 6

12FTN 1/2-20 FINE N/I LOCK NUT 2

716SAEW 7/16 SAE WASHER 12

12SAEW 1/2 SAE WASHER 4

10X20MMB 10 X 20 METRIC BOLT/10.9 4

38SAEW 3/8 SAE WASHER 4

916FTN 9/16-18 NYLON INSERT LOCKNUT 8

916XTFW EXTRA THICK 9/16” WASHER 2

Instructions:

Front:

1. With vehicle on flat level ground, measure from center of front spindle to

the top of fender opening. Record measurement for later use.

2. Raise the front of vehicle in the center of the front cross member using

floor jack.

3. Support the vehicle on the frame cross member so that the front tire/wheels

are off the ground. Remove front wheels.

4. Remove the ABS line from the upper A-Arms using 10mm wrench. (See

Photo #1) Disconnect ABS/Brake line from steering knuckle.

5. Remove sway bar end links using 17mm. (See Arrow in Photo #2)

6. Remove cotter pin from outer tie rod. Disconnect tie rod using 12 mm sock-

et. (See Photo #3)

7. Remove cotter pin from upper ball joint, remove using 19mm socket. (See

Photo #4)

8. Locate lower shock mounting bolt. Remove lower shock mounting bolt

using 19mm socket. (See Photo #5)

9. Disconnect upper shock assembly from frame using 14mm wrench. (See

Photo #6)

10. Disconnect front sway bar from the frame.

Photo #1

Photo #2

Pg 1

2005-2006

Toyota Tacoma 2-2.5" - 3”

Platinum Series Coil Over

Installation Guide

Part# TC530K, TC530KS

I-TC530 01-26-06

Photo #3

1 2

Summary of Contents

Page 1

IMPORTANT NOTES-Skyjacker strongly advises taking extreme caution when working with loaded coil springs toprevent accident or harm.-Trucks w/o manual

Page 2

Pg 211. Assemble new Coil-Over as shown in Photo #7. Attach new sky-jacker coil over to new upper mounting bracket using the 1/2 x 2 1/2” finethread

Comments to this Manuals

No comments

Skyjacker TC530 User Manual

Browse online or download User Manual for For the car Skyjacker TC530. Skyjacker TC530 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Skyjacker TC530